Technica specifications
Model
XQG50-S1016
Automatic Drum Washing Machine
XQG50-S1016
Item
Main power
220V~/50Hz
10
0.05P1
300
Max working current(A)
Water pressure(MPa)
Washing power(W)
Spining power(W)
Washing capcity(Kg)
Spinning speed(rpm)
Drying power(W)
Size(high,depth,width)mm
Table of Contents
Before using
Names of parts---------------inside front cover
Matters needing attention-------------------1-3
Installation---------------------------------------4-5
Control panel--------------------------------------6
Operational functions-------------------------6-7
700
5
1000/800/600
1000
850‚550‚595
During using
Program selection-----------------------------8-9
Weight(Kg)
78
Preparations-------------------------------------10
Washing methods------------------------------11
Additional information-------------------------12
Maintenance
Maintenance-------------------------------------13
Warning code------------------------------------14
Trouble shooting--------------------------------15
Warning-------------------------------------------16
Wiring circuit-------------------------------------17
Technical specification------------Back cover
Warning
Matters needing attention
Safety
1.If the supply cord is damaged, it must be replaced by a special cord or assembly available
from the manufacturer or its service agent.
1. A separate earthed socket is required for the 2. Pull the plug and not the electric cable
power supply. After installation of the washing
machine the power plug must be accessible
during normal operation.
when unplugging the washing machine.
2.If a stationary appliance is provided, with a supply cord and a plug, the instructions shall
state that the appliance must be positioned so that the plug is accessible.
Note: this requirement does not apply if the appliance incorporates other means for
disconnection from the supply.
3.For washing machines with ventilation opening in the base, do not place directly on carpet
as it will obstruct the openings.
4.The instructions shall state that the appliance is to be connected to the water mains using
new hose-sets and that old-sets should not be reused.
3. Fuses in the power circuit should be rated for 4. For you safety, dry your hands before tou-
15A. Contact a washing machine technician or ching the washing machine and wear appro-
a desiganted service point for power cable
replacement.
priate footwear.
Note: these instructions are not required if the hoses are permanently attached to the
appliance.
5.When connecting the washing machine for water supply and drainage, make sure the plug
is within reach.
6.Keep the vent outlet at the bottom of the washing machine free from being blocked.
7.To prevent danger, damaged electrical cables must be replaced by the manufacturer or an
authorised service agent.
5. Do not use flammable detergents or dry c-
leaning agents; do not use flammable sprays
near the washing machine; do not remove or
insert the plug in the presence of flammable
gas.
6. The door of the washing machine beco-
mes hot during the water heating or drying
process. Avoid contact with the door during
the heating or drying process. For safety,
keep children away from the washing ma-
chine.
7. Do not allow children to play with the packing materials after unpacking.
16
1
Matters needing attention
Trouble shooting
The following circumstances do not constitute problems. Do not contact the maintenance
service until the problem has been confirmed.
8.The washing machine must not be used in 9. The washing machine should be placed
the open or in an area of high humidity as
water droplets may form on the electrical
components. Air dry the appliance if the
washing machine components become wet.
in a well-ventilated area, leaving a space
between the appliance and adjacent walls or
furniture.
problem
Possible Cause
Poor connection to power supply
Power failure
The washing machine fails to
operate
Door is not closed properly
Machine has not been switched on
Water is not turned on
Water pressure is less than 0.05MPa
The inlet hose has a kink
Water supply failure
The washing machine does not
fill with water
10. Keep away from heat sources and direct 11. During installation, ensure that the
sunlight to prevent plastic and rubber com-
ponents from ageing.
electric cable is not trapped by the washing
machine and damaged.
Dear customer, For the machine and your
own security, DO NOTREPAIR IT BY YOUR-
SELF! DO NOT USE THE WASHING MA-
CHINE WHICH SOME PARTS ARE LOST!
The door is not closed properly
Check that the height of the water hose is within 80-100cm
Check that the drain hose is not syphoning
The water supply and drainage
do not stop
Drainage hose is blocked
Drainage failure
Drainage hose end is more than 100cm above the floor
level
Check that all packing bolts have been removed
The washing machine is located on an uneven surface of
is not level
Check that all foam packing has been removed from the
motor
Strong vibration during spin
drying
Operation stops before com-
pletion of the wash cycle
Water of electricity failure
Use
1. Make sure that the washing machine is
securely connected to the water supply. Take door and then close the porthole. Do not shut
the necessary precautions or contact the lo-
cal service centre if the connection is poor or
there is a water leak.
2. Fasten the door handle before opening the
The detergent is not a low foam type
Excessive detergent has been used
Excessive foam in the drum
Failure of the drying process
the door violently.
Poor connection to the power source
Door is not closed properly
Program has not been correctly set
Check to see if the end of the water drainage hose is
submerged in water
Incomplete drying
The filter is blocked
The machine is overloaded
The water tap is not tured on
2
15
Warning code
Matters needing attention
Warning
Abnorma item
code
Checking position and
ask for help
3. Never place heavy objects, e.g. a heating
appliance or water container, on the top panel materials.
of the washing machine.
4. Do not wash foam rubber or simalar sponge
Content of identification Action to take
The water level can not
Warning and
Check if the water
pressure is low or stops
supplying
reach the reset water
stop running
level within 5 minutes
E11
E12
Water supply
The water level can not
Check if the water
pressure is low or stops
supplying
Warning and
reach the setting water
stop running
level within 8 minutes
The water level can not
reach the reset level in
8 minutes after drainage stop running
starting
Check if the water outlet
of the drainage and
adjust it and restart the
machine
Warning and
Drainage
5. Before washing, close zippers, buttons,
laces and repair damaged areas. Underwear the wash cycle. Otherwise, the water will spilt
6. Do not open the detergent dispenser during
and amall items should be palced in a laun-
dry bag or pillow slip. Do not wash clothes
containing wire frames.
out from it and the detergent can not be wash-
ed out completely.
The water is above the
warning level
Warning and
stop running
Ask the technician to
repair
E13
E31
Water supply
The feedback signal do-
es not change in 8 minu-
tes during the motor runs
Warning and
stop running
Ask the technician to
repair
Motor
Water level is
abnormal in the setting water level during
drying process
The water is ablove the
Check if the water outlet
of the drainage and adjust
it and restart the machine
Warning and
stop running
EA3
EC1
the drying process
No heating and
washing with
cold water
The water temperature
unchanged in 10 minutes
Ask the technician to
repair
Heater
7. The door is fitted with a self-locking device 8. After washing, turn off the tap to prevent
and can be opend when it is under the safety leaking; unplug the washing machine and
Water tempera- The drying sensor circuit Warning and
Ask the technician to
repair
state ( water should be under the safe level;
temperature inside the drum should be less
than 55§; the drum should do not run). Do
not open the door except above condition
otherwise the self-locking device will be
damaged and the operator will get hurt.
wipe clean the lower part of the porthole.
EC2
EC3
ture sensor
short cut or open
stop running
Water level
sensor
The water level sensor
circuit short cut or open
Warning and
stop running
Ask the technician to
repair
Within 30 minutes of dry
The temperature phase there is 5 minutes Warning and
Ask the technician to
repair
EC4
of air vent
in which the temperature stop running
is not increasing
The dry tempe- The heater sensor circuit Warning and
Ask the technician to
repair
EC5
U01
U02
rature sensor
short cut or open
stop running
Can not unlock after 4
times try
Warning and
stop running
Ask the technician to
repair
Unlock the door
9. Keep the door slightly open when the wa-
10. The tumble dryer should not be used if
Can not lock the door
after 4 times try
Warning and
stop running
Ask the technician to
repair
Lock the door
shing machine is not being used. Never cover industraial chemicals have been used for
the machine a
plastic sheet.
cleaning
Spin low speed
and cancel
drying
The judgement of un-
balance is above 1000g
Disperse the clothings
evenly in the tube
U03
Spin lopsidedly
11. The appliance must not be installed behind
a lockable door, a sliding door or a door with
a hinge on the opposite to that of the tumble
dryer.
U04
E22
Unclose the door The door is unclosed
Warning
Close the door
The memory
Ask the technician to
repair
EEPROM goes wrong
function is failure
Warning
14
3
Installation
Maintenance
1. Remove the power plug, open the porthole
and turn off the tap after washing to avoid to
produce damp and strange smell in the drum.
If the washing machine is not going to be used chine and rube apares. Only
for a long period of time, put the drainage hose the clothing soaked with some
as lower as possible to let the water in the pipe soap liquid is suggested.
out for avoiding the water turns bad quality and Warning: Remove the power
2. The dissolved agent and anti-
septics should not be used to
clean the surface of the ma-
As shown in Fig.1, remove all the packing materials
( in cluding the foam base ). It is normal that there are
some water drops on the plastic bag, the cushion and
the porthole. It is because of the water testing before
leaving the factory.
Fig.1
then put the pipe to the original place.
socket before the cleaning.
Check attachments and materials
3. Clean the detergent
cartridge regularly:
Pull the detergent cartridge
up and out then wash it out.
Put it back when it is clean.
4. To prevent blockages to the
water supply or the ingress of
contaminants, clean the water
inlet and inlet water filter
regularly.
Operational Quality
Water
hose
Drain
holder
Plastic
plugs
Name
manual
certificate
5. Clean the filter ( once a month )
Press the lower edge of the filter compartment
cover to open; ( Fig.1-2 )
Remove the filter by turning counterclockwise;
( Fig.3 )
Flash clean with running water;
Filter replacement is the reverse of removal.
Caution: Attention shall be paid to ensure that
the filter is replaced correctly to avoid possible
leakage.
Using a flat-nose screw driver prizes the slits
of two ends of the button panel and move the
panel out with your hands. ( Fig.4-5 )
6. If the machine is to be moved a distance
location, replace the vibration mounting locks
which were removed during installation as
shown below.
Quantity
1
1
1
1
3
Remove the packing screws as shown in Fig.2.
The packing bolts protect the appliance from impact damage during
transportation. Follow the steps below before using the appliance.
1. Remove the rear panel of the washing machine;
2. Remove the three packing bolts from the rear panel of the washing
machine, the rubber hose and then the shock ablorption steel channel;
3. Refit the back plate;
Replace the
rubber plugs
Remove the
back cover
4. Fill the holes left by the packing bolts with plastic plugs.
( Attention: the packing bolts and rubber hose should be kept in a
safe place for later use )
Insert the channel
steel vibration locks
insert the bolts
Tighten the bolts
with a spanner
There is a plastic jacket packing the door catch, please remove it
when you unpack the machine. Do not let children touch it to void
dangerous things.
Fig.1
Fig.2
Fig.3
Fig.2
Adjusting the position of the washing machine.
Fig.4
Fig.5
Replace the back cover
The washing machine is provide with adjustable feet. Before use,
adjust the feet until the appliance is level, as shown in Fig.3.
7. Remove the power plug and turn off the tap and open the door if the machine is not going
to be used for a long period of time. With the method there would not be any bad smell inside
the tube.
Fig.3
4
13
Installation
Additional information
Connection of water inlet hose and washing machine
( Using new hose-set and old hose-set should not be reused. )
Tips
water inlet hose nut
Adding the soften agent can help the laundry to get rid of the static electricity and
make the cloths feel softly and easy to iron.
Place the water inlet hose nut on the connector
of the water inlet valve.
The following list shows the drying time for the different quantity and kinds of the
laundry. You can select the expected drying program in accord with the quantity
and the drying degree. The selected program will be over when the drying process
is finished.
Slightly shake the water inlet hose nut to see
if it is tightly and properly fixed.
connector of water inlet valve
Water drainage hose
The height of the terminal of the water drainage hose
should be between 80-100cm. The water drainage
hose must be securely placed on the clip on the back
of the washing machine.
Weight of laundry
( Kg )
Remain time
( min )
Time for drying
Standard
Drying degree
Use the water drainage support supplied as an acce-
ssory for proper installation of the water drainage hose.
Fix the water drainage hose support with waterproof
string. Do not use an excessively long water drainage
hose and contract the authorized technician if the water
drainage hose needs to be extended. The water drainage
hose should not be extended more than 250cm ( longer
extension will result in concurrent water inflow and outflow ).
The diameter of the extension hose should be the same as
the original hose.
0-1
59
Dried
Dried
1-2.5
120
0-1
Dried
Caution: Water drainage hose must not be immersed in water.
The original and extension hoses should be tightly connected.
60min
30min
60
30
1-2.5
0-2.5
For ironing
Connection of power supply
Dry and
anti-becterium
program
Check the following items before connection to the power supply.
The socket conforms to the maximum power load ( The maximum current
load of the socket and power supply cable should not be less than 15A ).
Power supply voltage conforms to the required value.
The power supply socket and the plug of the washing machine compatible,
if they are compatible, refer to a washing machine technician or a designat-
ed service point for power cable replacement. The washing machine should
be connected to the earth before use.
12
5
Control panel
Installation
Reference loading
Laundry loading
Door lock
Remaining time:Min
Water level
Overalls
(cotton 950g)
Jeans
(800g)
START
PAUSE
WATER
LEVEL
Standard
Habit
Quick
Night
Heavy
Delicate
DELAY
TEMP
PREWASH
Evenly load the laundry in the
washing machine and then
tightly close the door of the
washing machine.
Pajamas
(200g)
Blended
(fabric clothes
800g)
Standard
60min
30min
POWER
ON/OFF
00
rpm
Min
Time
Shirts
(300g)
PROGRAMME
WASH
RINSE
DRAIN
DRY
Shirt
(cotton 300g)
Underwear
(blended fabrics 70g)
Notice:
1) When first using the
Jackets
(cotton 800g)
Socks
(blended fabrics 50g)
washing machine, let it run
unloaded for one program to
prevent the laundry from being
tainted by oil or dirty water from
the washing machine.
Woolen
(blankets 3000g) sheets
(cotton 800g)
Single bed
A. POWER ON/OFF
Touch this button to swith on the power if the machine is not on power, and touch this
button to switch off the power if the machine is on power.
2) Do not overload the washing
machine.
B. PROGRAMME
Touch this button then you can select the washing programs as you wish from top to
bottom in proper order. The backlight is bright while the program is selected. The
machine will carry out the standard program if there is no program to be selected.
Attention: The machine has the memory function for the "Habit" program.
Put detergent in the cartridge
C. DRY
There are three partitions in the detergent cartridge:
Partition 1 : It is used for the prewash function.
Partition 2 : Put the detergent in this partition no
matter whether the prewash function is selected or not.
Partition 3 : Put the softening agent in this partition if the
launry has gone through the soften process.
The sequence of the dry program as follow as each time the button is touched after the
washing program is set:
Whole auto dry program.
The standard program for the individual dry.
At this moment you can select either 60 min or 30 min program.
You can not select dry function while you have already selected the heavy or delicate
program.
Caution: 1) Do not add liquid degergent into partition 1 and partition 2
2) For prewashing program, detergent should be added to both partition 1
and 2; for other programs, do not add detergent to partition 1
Attention: The maximal quantity of the laundry is 2.5Kg if the dry function is selected.
3) Do not overuse softening agent as this may damage artificial fabrics
D. DRAIN
The different spinning speed can be selected by touching this button. For details please
see the program setting guide.
The spinning speed is 1000rpm ( 800rpm for night washing ) if the dry function is
selected.
Washing program setting
Set the washing program correctly in accordance with the laundry load.
First connect the mains and depress the power on/off button, the machine will work on
the defaulted standard program. Depress the program selection button for the required
washing program.
E. RINSE
Touch this button to select the rinsing time. The time is changeable each time when it is
touched and 6 times are the maxim.
Notice: The above operation should be under the condition of no power down. The ma-
chine will continue its previous program if the machine has the memory function after
the power down. The memory function can be canceled by turning off the power and
restart it.
F. WASH
Touch this button to select the washing time. Increasing the washing period each time
this button is pressed. The increasing step is one minute for one press.
6
11
Preparations
Operational functions
G. DELAY
Power supply
Water supply
Setting the finished time of the scheduled washing by touching this button. The defaulted
time for the scheduled washing is 9 hour. The washing time can be increased one hour by
one touching of the button. If the button is pressed and held the time can be varied from 1
to 24 hour cyclically till the button is released. If the START/PAUSE button is pressed the
current setting is confirmed after the scheduled washing program is ready.
If the time for the washing program is longer than the time of the scheduled washing then
the program will work immediately after the START button is pressed.
Attention: There are some different between the setting time and actual time because of
the water temperature, water pressure and the distributions of the laundry in the tube.
There is no scheduled washing function for "Delicate" program.
Plug in the power supply
220V/50Hz
Turn on the tap ensure that the
water is clear.
Caution: Before starting the
washing machine turn on the
water faucet to ensure that the
water faucet and the water inlet
hose are connected correctly and do not leak.
Detergent selection
Laundry treatment
The washing result depends on the
quality of the detergent except the
function performances of the washing
machine. There are many brands of
detergent in the market. For the best
washing result, we suggest you using
the special on-form detergent that
produced for the auto drum washing
machines.
For washing the wool and the chemi-
cal fibre please use the special deter-
gent for those materials. Do not use
dry-clean dissolvent.
Attention: Only put the quantity of the
detergent in the cartridge for one time.
Sort out clothes according to type and extent
of dirt. There are three types of clothes:cotton,
synthetical and woolen ( silk ) fabrics.
Separeate white clothes from colored. If whites
and coloreds are combined for one load, make
sure the coloreds are coloreds are colorfast.
H. Remaining time: Min ( Digital display screen )
This display unit is used for warning the washing time left and fault information. It can
display the setting time of scheduled washing and heating temperature. The screen only
display the hour if the time setting is over 10 hour.
I. TEMP ( Children lock )
Touch this button to set washing temperature. The temperature is changed cyclically each
time the button is pressed. For the highest temperature setting of each program, please see
the program setting guide. The "Delicate" program there is no temperature setting function.
To lock button on the control panel by pressing this button for 3 second, which including
the POWER button. These can be unlocked if thise button is pressed for another 3 second.
- Remove all objects from pockets that may cause
damage to the machine, such as keys and coins.
J. PREWASH
- Clothing with frayed edges or yarns should be
put in a wash bag or special bag before washing.
- Repaier damaged clothing, lose buttons or
damaged zips and hooks efore washing.
- Bed sheet and table ware should be loosely
loaded and not folded.
This washing machine is for household use and
designed for mechanically washable clothes.
When washing, separate unwashable clothes
with reference to clothes labels.
The prewash function can be added into the washing program.
K. WATER LEVEL
The related time and water level in the drum can be selected by pressing this button in
accord to the laundry quantity. The more bright the indicate light the more high the water
level in the drum and the default washing time is longer with this height. The quantity
indicator changes its position accordingly each time the laundry quantity button is pressed.
We suggest using the first gear when the quantity is less than 1 Kg. And using the second
gear when the quantity is less than 2.5 Kg. And using the last gear when the quantity more
than 2.5 Kg. All other program setting indicate the default values when the laundry quantity
is set. For each setting range please see the program setting for reference. The default
program will be carried out if the function is not selected.
Wash load
L. Door lock indicator
This lamp is light when the door is locked and the machine is in the operation state and the
door can not be opened. If the condition for opening the door is met, press the START
/PAUSE button this lamp is off and the door is unlocked and the door can be opened.
Non-fade
cottons
Type
Delicat fabrics Woolen fabrics Blending fabrics
M. START/PAUSE
Max load
5kg
2kg
1kg
2.5kg
The set program is carried out while this button is pressed. To pause the current program,
just press this button and the program will not operate at the moment. Pressing this button
again if you want to resume the operation. The program can not be reset in the process of
running or pause state. Turning off the power and turning on it again if you want to reset
programs.
10
7
Program selection
Program selection
Program and washing time
The methods for using detergent
Partition1 Partition2 Partition3
Program and washing time
Wash ( min ) Rinse ( time )
Total time consume
( min )
Program
name
Suitable
condition
Drain ( rpm )
Temp ( ¤& )
Option
/
Quantity
Default
Range
/
Default
Range
Default
Range
/
Default
Range
/
Default
/
Range
/
add 12 minutes
washing
Prewash
Standard
for dirty cloth
below 5 kg
/
/
/
/
wash/rinse
/spin
wash/rinse
/spin/dry
wash/rinse
/spin/dry
wash/rinse
/spin
wash/rinse
/spin/dry
wash/rinse
/spin/dry
800
0/600/800/1000 cold
0/600/800/1000 cold
cold/30/40/60/90
cold/30/40/60/90
59
7-185
7-299
below 5 kg
below 2.5 kg
below 1 kg
below 5 kg
25
21
17
5-60
5-60
5-60
3
2
2
0-6
0-6
0-6
ordinary cloths
washing
1000
168
1000
800
0/600/800/1000 cold
0/600/800/1000 cold
0/600/800/1000 cold
0/600/800/1000 cold
cold/30/40/60/90
cold/30/40/60/90
cold/30/40/60/90
cold/30/40/60/90
103
59
7-235
7-185
7-299
7-235
self defined
washing program
according to the below 2.5 kg
habit of the
operator
25
21
17
5-60
5-60
5-60
3
2
2
0-6
0-6
0-6
Habit
Quick
1000
1000
168
103
below 1 kg
wash/rinse
/spin
800
0/600/800/1000 cold
cold/30/40/60
32
7-168
below 5 kg
below 2.5 kg
below 1 kg
below 5 kg
8
6
5-60
5-60
5-60
5-53
2
2
2
3
0-6
0-6
0-6
0-6
wash/rinse for not very dirty
1000
1000
0/600/800/1000 cold
0/600/800/1000 cold
cold/30/40/60
cold/30/40/60
151
89
7-282
7-218
/spin/dry
wash/rinse
/spin/dry
wash/rinse
/spin
cloths
5
25
800
800
800
600
0/600/800
0/600/800
0/600/800
0/600
cold
cold
cold
cold
cold/30/40/60
cold/30/40/60
cold/30/40/60
cold/30
67
184
118
62
7-177
7-292
7-228
7-164
wash/rinse
/spin/dry
wash/rinse
/spin/dry
Night
for night washing below 2.5 kg
below 1 kg
20
15
40
5-53
5-53
5-60
3
3
3
0-6
0-6
0-6
wash/rinse
/spin
for thick or heavy
below 5 kg
cloths
Heavy
wash/rinse
/spin
cashmere and
wool fabrics
dry the ordinary
below 2.5 kg
laundries
dry the ordinary
below 2.5 kg
laundries
Delicate
Standard
60min
below 2 kg
6
1-15
2
/
0-6
600
0/600
cold
cold
29
120
60
3-82
120
60
dry
dry
dry
120
60
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
anti-virus process
for dried laundry
30min
below 2.5 kg
30
/
/
30
30
Notice:
indicates that softener or bleach can be added if needed
indicates that detergent must not be added
indicates that detergent must be added
Attention: The above list is just for your reference since the temperature, water pressure and function you
selected may verify for different laundry.
8
9
|