BATTERY DRIVEN, FTP-608 Series
2” HIGH SPEED THERMAL PRINTER
FTP-628MCL053/054
■ OVERVIEW
The FTP-628 MCL Series are battery driven high-speed
ultracompact printers with a 2-inch paper width equivalent.
Paper can be easily set using our unique platen release
mechanism.
The FTP-628 MCL Series can be used for a variety of
applications, such as portable terminals, POS, ticket issuing
terminals, label printers, banking terminals, and measurement
and medical equipment.
■ HIGHLIGHTS
• Ultra compact
Height 15.5 mm, width 69.6 mm, depth 34.3 mm
• High speed printing
It can print at 60 mm/s (480 dotlines/s) maximum by using
Fujitsu's unique head drive control.
• High resolution printing / Kanji supported
8 dots/mm of resolution printing is possible.
• Easy paper setting
Our unique platen release mechanism allows a
wide paper route even if the printer is ultra-compact, so
paper can be easily inserted. Conventional auto loading is
also available.
• Two types of paper routes
Front or bottom feed, depending on the paper route.
• Easy mounting
Wiring for the head, motor, sensor are housed within one
flexible cable (053, 054) or in two cables (051, 052). The
mechanism can be secured by one hook and two screws at
two locations, making mounting easy.
1
FTP-628MCL053/054
■ SPECIFICATIONS
Item
Specification
Interface
Conforms to RS232C / Centronics
4.2 - 8.5 VDC average current, 0.87 (0.93) A peak value
(print ratio: 12.5%, print speed: 50mm/sec. at 7.2V )
For print head
Power
supply
4.2 - 8.5 VDC, 1A maximum
Note: 5.8 to 8.5 V is recommended for automatic paper loading
For motor
For logic
5 VDC ± 5%, 0.1 A maximum
72.3 x 34.3 x 15.5 mm (WxDxH)
69.3 x 52 x 15 mm
Printer mechanism
Interface board
Printer mechanism
Interface board
Dimensions
Weight
Approximately 47g (without knob)
Approximately 20g
Pulse resistance: 100 million pulses/dot (under our standard
conditions)
Head life
Abrasion resistance: paper traveling distance 50km (print ratio:
25% or less)
Operating temperature*
Operating humidity
Storage temperature
Storage humidity
0˚ C to +50˚ C
20 to 85% RH (no condensation)
-20˚ C to +60˚ C (paper not included)
5 to 95% RH (no condensation)
Operating
environment
Head temperature
detection
Detected by thermistor
Detection
function
Paper out/mark detection Detected by photo-interrupter
Head up detection
Detected by micro-switch
High Sensitive Paper
Standard paper:
TF50KS-E4 (Nippon Paper)
TF60KS-E(Nippon Paper)
FTP-020PU001 (58mm)
PD105R (Oji Paper)
FTP-020P0701 (58mm)
Recommended thermal sensitive paper
Medium Life Paper
TF60KS-F1
FTP-020P0102 (58mm)
PD170R (Oji Paper)
P220VBB-1 Mitsubishi
Paper)
Long Life Paper
PD160R-N (Oji Paper)
*+5˚C to +40˚C printing density assurance rance (-25 to 70˚C capability)
3
FTP-628MCL053/054
■ DIMENSIONS
1. Printer mechanism
FTP-628MCL054
FTP-628MCL053
Unit: mm
Note: 1. Dimensions are nominal value (tolerance ±5 unless otherwise specified).
2. Platen unit (lever, platen, etc) moves by approximately 0.7mm toward paper insertion direction when platen is
open.
2. Interface board
Unit: mm
4
FTP-628MCL053/054
Connector (FPC) specification
(1) Connector
Mechanical unit side:
Remote side (housing site):
FPC connector
52030-3090 (made by Molex)
(2) Pin assignment on the mechanical side
No
1
Signal
I/O Contents
PHK
VSEN
PHE
SW1
SW2
VH
—
I
Cathode for photo interruptor
2
paper sensor power
3
O
O
I
Emittor for photo interruptor
Platen release switch
Platen release switch
4
5
6
I
Head drive power
Data in
7
VH
I
8
DI
I
9
CLK
I
Synchronous clock for communication
10 GND
11 GND
12 STB6
13 STB5
14 STB4
15 VDD
16 TM
—
—
I
Ground power supply for thermal head
I
Thermal head energizing control signal
I
I
Logic power
O
O
I
Thermally sensitive resistor input termnial 1
Thermally sensitive resistor input termnial 2
17 TM
18 STB3
19 STB2
20 STB1
21 GND
22 GND
23 LAT
24 DO
I
Thermal head energizing control signal
I
—
—
I
Ground power supply for thermal head
Data latch
Data out
O
I
25 VH
Power supply for thermal head
26 VH
I
27 MT/A
28 MT/A
29 MT/B
30 MT/B
I
I
Stepping motor excitation signal
I
I
5
FTP-628MCL053/054
■ FUNCTION OF INTERFACE BOARD
Item
Item
1.
2.
3.
4.
5.
6.
7.
Test print function
8.
9.
Motor power saving function
Mark detection function
Paper out detection
Paper near end detection
Platen open detection
10. MCU operation abnormality detection
11. Power ON/OFF sequence protection
12. Motor over-current protection
13. Hardware timer
Thermal head temperature abnormality detection
Blow-out fuse detection
Head voltage abnormality detection
Sensor (Photo-
interruptor)
Platen unit
Thermal head
Motor
FPC
Connect terminal:
surface side
Connector No
30,29, .....................2,1
(FPC pin numbers)
Europe
Japan
Fujitsu Components Europe B.V.
Diamantlaan 25
Fujitsu Component Limited
Gotanda-Chuo Building
2132 WV Hoofddorp
Netherlands
Tel: (31-23) 5560910
Fax: (31-23) 5560950
Email: [email protected]
3-5, Higashigotanda 2-chome, Shinagawa-ku
Tokyo 141, Japan
Tel: (81-3) 5449-7010
Fax: (81-3) 5449-2626
Email: [email protected]
Fujitsu Components
International
Headquarter
Offices
Asia Pacific
North and South America
Fujitsu Components America, Inc.
250 E. Caribbean Drive
Sunnyvale, CA 94089 U.S.A.
Tel: (1-408) 745-4900
Fujitsu Components Asia Ltd.
102E Pasir Panjang Road
#04-01 Citilink Warehouse Complex
Singapore 118529
Tel: (65) 6375-8560
Fax: (1-408) 745-4970
Fax: (65) 6273-3021
Email: [email protected]
Email: [email protected]
© 2004 Fujitsu Components America, Inc. All company and product names are trademarks or registered
trademarks of their respective owners. Rev. 11/15/2004.
6
|